RT-678 Firestop cable coating

Universal solution to prevent the spread of fire through the cable jacket

Applications and advantages:

•Fire protection for cables in flammable insulation

•For single cable laying and cable bundles in trays

•For inside applications

•High thermal conductivity

•Does not overheat the cable

•For inside and outside application

TECHNICAL SPECIFICATIONS

Color

Total volume / filling / composition output

Fire resistance limit:
– for pipeline and air duct penetrations
– for cable penetrations

Scope of supply

Application equipment

Setting time

Recommended service life

Shelf life

Manufacturer

Country of Origin
Red / Gray

450 ml / 430 ml / 4.9 liters*


240 minutes
180 minutes

Composition cartridge, 2 mixers

RT-01D dispensing device

35 seconds

30 years

12 months

Rock Tech FZC

UAE

*For more information, refer to the TDS

NAMEPCSITEM NO.
RT-01 two-component fire-fighting thermally expanding composition, 430 ml1250053
RT-01D dispensing device1250050
RT-620-M additional spout-mixer1250011
Pos.DesignationName
1part No. 250050RT-01 two-component fire-fighting thermal expanding composition
2part No. 250053RT-01D dispensing device
3part No. 250012RT-M marking plate Sleeves
DN, mmDepth of firestop sealing, mmVolume, LQuantity of cartridges, pcs
50505050
80808080
80808080
80808080
50505050

* The total thickness of the penetration filling with fire protection material must be at least 80 mm for IET60 or 200 mm for IET150 (on either side of the penetration). If the penetration is filled on both sides, the thickness of each part must be at least 40 or 100 mm, respectively * The total cross-sectional area of the cable must not exceed 60% of the penetration area (i.e. RT-01 equals 40% or more of the penetration area). * It is allowed to install the following basic materials in the walls and floors: concrete, brick, gas silicate block, sandwich panel, fireproof gypsum board with the rated limit of fire resistance.

Pos.DesignationName
1part No. 250050RT-01 two-component fire-fighting thermal expanding composition
2part No. 250053RT-01D dispensing device
3part No. 250012RT-M marking plate Sleeves
DN, mmDepth of firestop sealing, mmVolume, LQuantity of cartridges, pcs
50505050
80808080
80808080
80808080
50505050

* The total thickness of the penetration filling with fire protection material must be at least 80 mm for IET60 or 200 mm for IET150 (on either side of the penetration). If the penetration is filled on both sides, the thickness of each part must be at least 40 or 100 mm, respectively * The total cross-sectional area of the cable must not exceed 60% of the penetration area (i.e. RT-01 equals 40% or more of the penetration area). * It is allowed to install the following basic materials in the walls and floors: concrete, brick, gas silicate block, sandwich panel, fireproof gypsum board with the rated limit of fire resistance.

Pos.DesignationName
1part No. 250050RT-01 two-component fire-fighting thermal expanding composition
2part No. 250053RT-01D dispensing device
3part No. 250012RT-M marking plate Sleeves
DN, mmDepth of firestop sealing, mmVolume, LQuantity of cartridges, pcs
50505050
80808080
80808080
80808080
50505050

* The total thickness of the penetration filling with fire protection material must be at least 80 mm for IET60 or 200 mm for IET150 (on either side of the penetration). If the penetration is filled on both sides, the thickness of each part must be at least 40 or 100 mm, respectively * The total cross-sectional area of the cable must not exceed 60% of the penetration area (i.e. RT-01 equals 40% or more of the penetration area). * It is allowed to install the following basic materials in the walls and floors: concrete, brick, gas silicate block, sandwich panel, fireproof gypsum board with the rated limit of fire resistance.

Pos.DesignationName
1part No. 250050RT-01 two-component fire-fighting thermal expanding composition
2part No. 250053RT-01D dispensing device
3part No. 250012RT-M marking plate Sleeves
DN, mmDepth of firestop sealing, mmVolume, LQuantity of cartridges, pcs
50505050
80808080
80808080
80808080
50505050

* The total thickness of the penetration filling with fire protection material must be at least 80 mm for IET60 or 200 mm for IET150 (on either side of the penetration). If the penetration is filled on both sides, the thickness of each part must be at least 40 or 100 mm, respectively * The total cross-sectional area of the cable must not exceed 60% of the penetration area (i.e. RT-01 equals 40% or more of the penetration area). * It is allowed to install the following basic materials in the walls and floors: concrete, brick, gas silicate block, sandwich panel, fireproof gypsum board with the rated limit of fire resistance.

Pos.DesignationName
1part No. 250050RT-01 two-component fire-fighting thermal expanding composition
2part No. 250053RT-01D dispensing device
3part No. 250012RT-M marking plate Sleeves
DN, mmDepth of firestop sealing, mmVolume, LQuantity of cartridges, pcs
50505050
80808080
80808080
80808080
50505050

* The total thickness of the penetration filling with fire protection material must be at least 80 mm for IET60 or 200 mm for IET150 (on either side of the penetration). If the penetration is filled on both sides, the thickness of each part must be at least 40 or 100 mm, respectively * The total cross-sectional area of the cable must not exceed 60% of the penetration area (i.e. RT-01 equals 40% or more of the penetration area). * It is allowed to install the following basic materials in the walls and floors: concrete, brick, gas silicate block, sandwich panel, fireproof gypsum board with the rated limit of fire resistance.

Have any questions?
Contact us!

Fill out this field
Please enter a valid email address.
Fill out this field
Fill out this field